A DSL Note: Using a power supply with a different voltage rating than the one included with the DSL - B will cause damage. Opening the cover will void any warranties on the equipment. A damp cloth can be used to clean the equipment. Do not use.
|Country:||Moldova, Republic of|
|Published (Last):||12 April 2006|
|PDF File Size:||4.26 Mb|
|ePub File Size:||8.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
Quick Links. Download this manual See also: User Manual. Table of Contents. Page 3 WAN Info Page 5: Front Panel View A solid light indicates a connection to an wireless is operational.
A flashing Ethernet-enabled computer on ports Page 6: Rear Panel View Reset Power Receptor Pressing the Reset button for 5 seconds restores Receptor for the supplied power the router to its original factory default settings. Note that either a crossover or straight-through Ethernet cable can be used.
The router automatically recognizes the type of connection that is required. Page 8 Then turn on and boot up your PC and any LAN devices, such as hubs or switches, and any computers connected to them. Page 9: Configuring Your Computer 4. Click on OK twice to save your changes and then close the Control Panel. Enter your user name and password, and then click OK to display the user interface. Note: This manual has been prepared using the admin user name.
To continue, click on the Next button. There is also an option to enable Quality of Service. When you are ready, click Next to continue. Select this option if required by your ISP. The following is a PPPoA example.
Click Next to continue. Select an appropriate network protocol and encapsulation mode. Then decide if you will be using any features such as dial on demand, PPP IP extension, keep alive and then click Next. For the example, NAT will be enabled. Leave the remaining fields at their defaults and click Next to continue.
Page 18 This next screen will allow you to enable the wireless function of your router. If you enable wireless, be sure to enter a wireless network name SSID to identify your wireless connection. You will need to know the wireless network name SSID to connect any wireless computers on your network to your router.
Click Apply to save your changes. Click Security to proceed to the wireless security section. Page Security Network re-auth interval is the time in which another key needs to be dynamically issued.
Page 24 Used by time-sensitive applications such as real-time video. When finished with your selections, click Next to continue. Note: These settings are ISP dependant. For information regarding proper configuration, contact your ISP.
Page 26 Internet. If selected, you will be asked to enter the static IP address. This screen will outline all WAN settings for review. When satisfied with the settings click the Apply button. Close the DSL Configuration window and wait at least two minutes before reopening your web browser. Enter one primary and one secondary DNS address in each field.
Click Apply to save the configuration. Enter the hostname and the interface that you are using. Also enter the username and password assigned by the DNS service. Click on Apply to save these configurations. A confirmation screen will appear confirming that you really want to log out.
Consult your ISP to determine the correct settings. Click Apply if you are finished or click on Advanced Settings if you want to configure more advanced settings. Test modes include normal, reverb, medley, no retrain, and L3. After you make your selection, click on Apply to save these settings first before you go to Tone Selection. Do not change these settings unless directed by your ISP. Page Virtual Server Internet e. This figure shows the Virtual Servers Setup page that allows you to configure your virtual server s.
Click on the Add button to configure a virtual server. Once you are satisfied with your selection, click Apply once. Page 38 The following screen appears after you save your selection. To add additional virtual servers, click on the Add button.
If you need to remove any of the server names, select its check box in the Remove column and click on the Remove button. Enter the IP address and click Apply. Click on the Add button to add incoming filter settings. Page 41 This next screen will appear when you click Add. Make sure at least one or multiple WAN interfaces are selected to apply the rule. Click Apply to save. Click on the Add button to add outgoing filter settings.
Page 43 IP filter. The screen lists the IP filters that were added from the previous screen. To add another filter click Add. If you click Change Policy, a confirmation dialog allows you to verify your change.
Select Yes to continue, or No to to cancel. Page 45 Click Apply to save. After you save the settings, a screen showing the settings will appear. On this screen you will be able to add, view and delete MAC filtering rules. Page Parental Control Enter a start and end blocking time. Click Apply to save the settings and continue. To proceed, click on Add. When complete, click Apply. When ready, click Apply. Page Quality Of Service This ensures that time sensitive data e.
You can configure the Quality of Service to apply different priorities to traffic on the router. Page 51 This screen allows you to add a network traffic class rule. A rule consists of a traffic class name and at least one condition. All configured conditions must first be met before the rule takes effect.
Click Apply to save any changes. Page Port Mapping Click on the Add button to create a mapping group. If you need to remove an entry, select the checkbox in the remove column next to the desired group and click the Remove button. Click Apply when finished. If you have an existing certificate, click on Import Certificate to retrieve it.
Page 55 Import your existing certificate by pasting the certificate content into the Certificate field and paste the private key into the Private Key field. Click Apply to submit the request to import the certificate. Enter the certificate name in the Certificate Name field. Paste the content of the certificate that you wish to add in the Certificate field and click Apply.
Page Wireless APs. The Wireless -- QoS section allows you to configure the wireless quality of service for the router. Page Wireless--Advanced A Beacon is a packet of information that is sent from a connected device to all other devices where it announces its availability and readiness. A beacon interval is a period of time sent with the beacon before sending the beacon again. The beacon interval may be adjusted in milliseconds ms. Page 59 High network traffic areas should select Short preamble type.
Transmit Power: This is the percentage of power that should be transmitted from your wireless router. Page Tools Click the Admin button to change the routers account passwords. Click the Services button to configure what services are allowed to pass through the router.
D-Link DSL-2640B User Manual
D-Link DSL-2640B Manual
Dlink DSL-2640B User Manual