ASTM D3139 PDF

Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals1 This standard is issued under the fixed designation D; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. This standard has been approved for use by agencies of the Department of Defense. Terminology greater than that of SDR 64 and intended for use in supply and distribution lines for water, using flexible elastomeric seals.

Author:Ner Gardagar
Country:Comoros
Language:English (Spanish)
Genre:Relationship
Published (Last):16 August 2016
Pages:70
PDF File Size:4.30 Mb
ePub File Size:17.75 Mb
ISBN:728-3-94142-195-7
Downloads:56239
Price:Free* [*Free Regsitration Required]
Uploader:Mezragore



Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals1 This standard is issued under the fixed designation D; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.

This standard has been approved for use by agencies of the Department of Defense. Terminology greater than that of SDR 64 and intended for use in supply and distribution lines for water, using flexible elastomeric seals. The test methods described are not intended to compression of an elastomeric seal or ring: be routine quality control tests, but are to evaluate the 3. These 3. It is the responsibility of the user of this 4. Materials and Manufacture standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior 4.

Referenced Documents have no deteriorating effects on the gasket and pipe materials. Current edition approved Mar.

Published March Originally 5. Last previous editionapproved in as D — DOI: of 6. Quincy Ave. The hydrostatic design basis for this joint design shall be established on a representative size at a minimuim test level of 10 points and h in accordance with Test Method D, except that the ends shall be restrained. Test pressure levels for establishing hydrostatic design basis shall be calculated on pipe minimum wall dimensions.

If the wall is not sufficient to withstand the com- pressive force, then a rigid tubular internal stiffener shall be FIG. A stiffener specified by the manufacturer for this purpose shall be used.

The the pipe spigot is deflected axially in the socket to the gasket shall be the sole element depended upon to make the maximum unstressed limit permitted by dimensional clearance joint flexible and water tight.

The gasket shall be a continuous between the spigot and bell. Dimensions, Mass, and Permissible Variations 7. Workmanship, Finish, and Appearance 6. The minimum wall thickness properties. Test Methods of the pipe barrel see Fig. The gasket shall be of such size and shape 8. Under such joint design and deflected to the limit defined in 5. No agreement, minimum requirements shall not be lowered, nor coatings, fillings, or packings, other than lubricants recom- tests omitted, substituted, changed, or modified, nor shall mended in 4.

If upon retest, failure occurs, After the pipe sections are fitted together with the gasket or the quantity of product represented by the test s does not meet gaskets in place, the assembly shall be subjected to separate the requirements of this specification.

Certification leakage at either pressure for the duration of either test. The pressure shall then be continuously increased to the minimum When specified in the purchase 8. Hg for 1 h with no leakage be furnished. Keywords 9. Rejection and Rehearing ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm. Learn more about Scribd Membership Home. Much more than documents. Discover everything Scribd has to offer, including books and audiobooks from major publishers.

Start Free Trial Cancel anytime. ASTM D Document Information click to expand document information Description: Standard. Date uploaded Mar 14, Did you find this document useful? Is this content inappropriate? Report this Document.

Description: Standard. Flag for Inappropriate Content. Download Now. Related titles. Carousel Previous Carousel Next. Jump to Page. Search inside document. An American National Standard Designation: D — 98 Reapproved Standard Specification for Joints for Plastic Pressure Pipes Using Flexible Elastomeric Seals1 This standard is issued under the fixed designation D; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

Kelvin Ng. Lingamneni Ravikiran. Hirmannazif Halil. Jorge Novoa. Arkaprava Ghosh. Francisco Guerra. Tim Rahul ferromet. Jonathan Topham. Hamed M. R Ali. Dalton Jay Casila.

Popular in Standards. Bernice Samina. Retaining Walls and Geotechnical Design to Eurocode 7. Bogdan Hritcu. Crispin Meneleo Valenzuela. Wawan Sudharsono. Bepe Bagus Panuntun. Munir Baig. Birjesh Kumar. Jaime Colvatel. Sai Yakkala. Samy Posso. Prashant Shinde. Vivek Agarwal. ISO and how it impacts medical device companies.

KOLB AND WHISHAW AN INTRODUCTION TO BRAIN AND BEHAVIOR PDF

ASTM D3139

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser. This option is mobile friendly and compatible with all devices, including mobile tablets and smart phones. The PDF Download is licensed per individual in which the individual can place on up to four electronic devices for their personal use. Distribution of the PDF is not permitted. For a volume license the PDF is licensed to the person in which it is assigned. Use on a local area network or other network is not permitted.

ESORCISMO DI LEONE XIII PDF

Popular Publishers

Historical Version s - view previous versions of standard. Work Item s - proposed revisions of this standard. More F This specification covers the two types of joints, mechanical joint and push-on-joint, required for plastic pipe pressure systems with a wall thickness equal to or greater than that of SDR 64 intended for use in supply and distribution lines for water using flexible elastomeric seals. The joint shall be designed to provide a permanent seal, with surfaces free of imperfections that could adversely affect its performance.

Related Articles